Trenton Anvil made in Columbus, Ohio Serial number dates it to 1901, the 3rd year of production. A good user's anvil for blacksmiths or bladesmiths. So it's a Trenton. That part is pretty easy. There are no numbers or letters on it. Logarithmic charts in numbers for mac. The anvil had some crazy good rebound. Trying to figure out it's age and how it's made. I can't seem to find a seam on the top where a tool steel plate would be. Again, it rebounds and rings like crazy. Also, it had some interesting marks on the waist of the anvil. Details about Vintage Trenton 257lb Anvil 1930'S Trenton #130908 Anvil- Will ship. TRENTON LOGO WORN OFF SERIAL NUMBER + MEASUREMENTS MATCHES TRENTON.
Greetings, According to my quick read of Anvils in America you have: A Columbus Forge and Iron made anvil. (Columbus, OH.) Probably with a cast iron base welded to a solid wrought upper works. (weld at the waist.) Serial number 18199 would have been 1900.
(1900 ran from 12001-20,000) Very good quality anvils. Looks like yours is in pretty decent shape. There were Trenton anvils imported from Germany before 1890, but this isn't one of them. The feet details are wrong.
So it's definitely a CF&I anvil. I would say you have scored well. Regards, Brian. I would have to agree, that it is not a Trenton (unless it is an early one). I have a 1926 built 158# Trenton #193904, and you can see the hammer marks up and down the whole waist under the tail and the horn. Also the pocket on the underside is oval and not shaped to match the foot.
Trenton Anvil Company
Early CF&I anvils were cast base, not sure if they continued that into the Trenton line. On mine the weight and serial are heavily stamped, but the Trenton marking is barely there, can only make out the `ento' part of the name. Sns hdr pro 1 4 22 1 watermark remover mpt fort. For those who don't know it, Columbus Forge & Iron was started by Sy and Carl Wright (descendants of anvil maker Peter Wright), They forge welded the Trenton Anvils under a Steam Hammer.
If you look at the image on the front of Anvils in America, that is a painting by Nathan Green (painted in 1996), based on photographs of anvils being made at CF&I, the fellow in the center is Carl, and Sy is the fellow on the tongs. The history above is from a friend who knew Richard Postman. Below was also related to me when I was looking for more info on my anvil back in 2007. `As an aside, Mr. Postman told me he had met someone who had worked for CF&I before they closed. He noted the old metal sided building was hot as a furnace in summer and cold as a freezer in winter.
Trenton Anvil Serial Numbers List
He commented, apparently with pride, they had only one guy pass out due to the heat. Most of their workers were either direct or first generation Europeans and then mostly from Eastern Europe, such as Poland.' Kinda speaks about the type of immigrant workers we used to get plenty of in previous generations, and occasionally still get. Sorry to hear about your experiences with Iforgeiron. Some sections are more active than others, and replies depend on how many other topics are hot, moving yours down the list (same with any forum).
I havn't tried to setup a new profile after the last upgrade, but when I did it was easy and straight forward. If a topic gets burried you may have to bump it (create a new message in it to bring it to the top of the list).
When was the last time you tried to contact the moderators? Here is the current Contact us page: The General discussion page, of course is the most active, but the others tend to see daily activity, it all depends on what people are looking for info on and how many visit. Regards, Rich C.
Trenton Anvils History
Welcome to the The Garage Journal Board forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please,!
If you have any problems with the registration process or your account login, please contact. I thought it would be fun to guess at the weight. Bcm94312hmg driver for mac.
Old Trenton Anvil Serial Numbers
Along with guessing, I tried to reference Richard Postman's Anvils in America and at 32-1/2' long it fits the overall length for 250 lb as listed in the Hay-Budden section. A popular sized 150 lb Hay-Budden is listed as having a 4 x 16-1/2' face plate and 10-1/2' horn for an overall length of 27' I will be very humbled when/if it is finally weighed it is under 200 lbs. I have included pictures of 85 lb and 200 lb Trenton manufactured Acme anvils as reference to change in scale as Anvil weight increases.
Nine: i thought it was a BIG UN. Now to see how good your purchase really was put a straight edge on the top from end to end and side to side to see how straight the top is. Also if you have a steel ball to bounce off the top to see if it bounces back into your hand for a great rebound. If those are great then you get a Father's Day YOU SUCK award and if not some anvils that don't pass the test have either been in a fire, abused or poorly made in the first place. Also my other suggestion as a nice piece of gym equipment is even better now that you have a 250 pounder. Better buy an inversion table to use if you are planning on moving it around much.
Trenton Anvil Sizes
Thread Trenton Anvil. Anvils with welds at the waist of the body were forge welded. The forge weld was made under steam hammers. I am unfamiliar with Trenton anvils, however, a lot of older anvils Hay Budden, Peter Wright coming to mind were made with wrought iron bodies. The wrought iron was cut into short bars and forge welded to form two large lumps. These were forged the approximate shape of the top and bottom of the anvil body and horn. Once these pieces were rough forged, they were forge welded at the waist. The anvil was then forged to nearly final shape, and the steel face plate was forge welded on. This face plate was then quenched to harden it. Trenton anvil serial number rating Low, Hp laserjet c3150a driver, Bastien piano basics primer level pdf. Large Antique Trenton Anvil. Dealers buying for resale may be exempt from paying sales tax if the dealer has a sales tax number and a signed tax exemption. TRENTONS manufacturing and industry date back to the. for a number of. An enterprise which attracted wide attention was the anvil works of. Need help identifying this Trenton anvil. I would recommend you coat the front face of the front foot with soapstone or flour and look harder for a serial number. Fully functional 5. Little Giant power hammer located 2. Ft. worth. Has 2 hp. Comes with one set of bolt on drawing. Has been well maintained and kept greased. Can someone tell me the date of my Trenton anvil Its serial number is A11076. It has the diamond with Trenton in it but also has a Buel Patent mark wi. Trenton anvil serial number Trenton anvil serial number I favor the fist level anvil height myself. Reason is unknown and may or may not be grenton to the above story. Hi Lester, According to Anvils in America, its a Trenton anvil, made by Columbus Forge Iron, Columbus OH. The Trexton bit was from a screwed up punch that they. You are bidding on a vintage Trenton anvil that is marked Trenton Solid Wrought USA M166 A15 579 on the front foot. This serial number A15579 puts her as being made. I admit to not knowing how Trenton anvils were made. A common method was to pour the body of the anvil with something like malleable iron or semi steel, incorporating a tool steel face plate in the casting. The face plate had lugs to key the face plate mechanically to the anvil body. Looking at the weld in the photos, I do not think the weld was run when the anvil was originally made. It has a typical weld bead with a wide weave, and there are dingleberries as would come from a poorly run stick weld or MIG weld. My belief is the anvil had been broken at the waist and re welded. I wonder as to the material of the anvil body. A weld on cast iron or semi steel would be run with a nickel based repair rod, and would appear brighter than the base metal and not so neat of a bead. The weld was run using a mild steel filler rod. This would point to the body of the anvil being a mild steel or semi steel casting. Wrought iron is not the easiest material to weld using welding processes such as stick or MIG. It has a stringy kind of structure with slag laying in the laminations. Forge welding is the best process for welding wrought iron. Stick welding with a small diameter electrodes using low heat will work, but some of the entrained slag in the wrought iron will often float up into the weld pool. Oxyacetylene welding is a process which can give a good weld on wrought iron as the welder can work the puddle to fuse in the wrought iron and float up the slag. Either way, welding wrought iron by processes other than forge welding is a somewhat difficult proposition. Whoever welded this anvil at the waist seems to have gotten a good weld, with good fusion and no undercut. As I said, I plead ignorance as to the material the body of a Trenton anvil would be made from, but the appearance of the anvil parting line on the beak or horn of the anvil seems to point to some kind of casting. Possibly, the body was cast from a mild steel or semi steel to take weld as it did. Interesting bit of detective work to determine how the anvil was made.